Apple II Technical Notes _____________________________________________________________________________ Developer Technical Support ProDOS 8 #20: Mirrored Devices and SmartPort Revised by: Matt Deatherage November 1988 Written by: Matt Deatherage May 1988 This Technical Note describes how ProDOS 8 reacts when more than two SmartPort devices are connected, how applications using direct device access should behave, and other related issues. This Note supersedes Section 6.3.1 of the ProDOS 8 Technical Reference Manual. _____________________________________________________________________________ Although SmartPort theoretically can handle up to 127 devices connected to a single interface (in practice, electrical considerations curtail this considerably), ProDOS 8 can handle only two devices per slot. This is because ProDOS uses bit 7 of its unit_number is used to distinguish drives from each other, and a single bit cannot distinguish more than two devices. When it boots, ProDOS checks each interface card (or firmware equivalent in the IIc or IIGS) for the ProDOS block-device signature bytes ($Cn01 = $20, $Cn03 = $00, and $Cn05 = $03), so it can install the appropriate device-driver address in the system global page. If the signature bytes match, ProDOS then checks the SmartPort signature byte ($Cn07 = $00), and if that byte matches and the interface is in slot 5 (or located at $C500 in the IIc or IIGS), ProDOS does a SmartPort STATUS call to determine how many devices are connected to the interface. If only one or two drives are connected to the interface, ProDOS installs its block-device entry point (the contents of $CnFF added to $Cn00) in the device-driver vector table, which starts at $BF10. In this particular instance, ProDOS would put the vector at $BF1A for slot 5, drive 1, and if two drives were found, at $BF2A for slot 5, drive 2 . If the interface is in slot 5 and more than two devices are connected, ProDOS copies the same block-device entry point that it uses for slot 5, drives 1 and 2 in the device driver table entry for slot 2, drive 1, and if four drives are connected, for slot 2, drive 2. Further in the boot process, if ProDOS finds the interface of a block device in slot 2 (not possible on a IIc), it replaces the vectors copied from slot 5 with the proper device-driver vectors for slot 2; this is the reason mirroring is disabled if there is a ProDOS device in slot 2. Note that non-ProDOS devices (i.e, serial cards and ports, etc.) do not have vectors installed in the ProDOS device-driver table, so they do not interfere with mirroring. When ProDOS makes an MLI call with the unit_number of a mirrored device, it sets up the call to the device driver then goes through the vector in the device-driver table starting at $BF00. When the block device driver (located on the interface card or in the firmware) gets this MLI call, it checks the unit number which is stored at $43 and verifies if the slot number (bits four, five, and six) is the same as that of the interface. If it is not, the ProDOS block device driver of the interface realizes it is dealing with a mirrored device, internally adds three to the slot number and two to the drive number, then processes it, returning the desired information or data to ProDOS. If an application must make direct device-driver calls (something which is not encouraged), it should first check devlst (starting at $BF32) to verify that the unit_number is from an active device. In addition, the application should mask off or ignore the low nibble of entries in devlst and know that one less than the number of devices in the list is stored at $BF31 (devcnt). The application then should use the unit_number to get the proper device- driver vector from the ProDOS global page; the application should not construct the vector itself, because this vector would be invalid for a mirrored device. The following code fragment correctly illustrates this technique. It is written in 6502 assembly language and assumes the unit_number is in the accumulator. devcnt equ $BF31 devlst equ $BF32 devadr equ $BF10 devget sta unitno ; store for later compare instruction ldx devcnt ; get count-1 from $BF31 devloop lda devlst,x ; get entry in list and #$F0 ; mask off low byte devcomp cmp unitno ; compare to the unit_number we filled in beq goodnum ; dex bpl devloop ; loop again if still less than $80 bmi badunitno ; error: bad unit number goodnum lda unitno ; get good copy of unit_number lsr a ; divide it by 8 lsr a ; (not sixteen because devadr entries are lsr a ; two bytes wide) tax lda devadr,x ; low byte of device driver address sta addr lda devadr+1,x ; high byte of device driver address sta addr+1 rts addr dw 0 ; address will be filled in here by goodnum unitno dfb 0 ; unit number storage Similarly, applications which construct firmware entry points from user input to "slot and drive" questions will not work with mirrored devices. If an application wishes to issue firmware-specific calls to a device, it should look at the high byte of the device-driver table entry for that device to obtain the proper place to check firmware ID bytes. In the sample code above, the high byte would be returned in addr+1. For devices mirrored to slot 2 from slot 5, this technique will return $C5, and ID bytes would then be checked (since they should always be checked before making device-specific calls) in the $C500 space. Applications ignoring this technique will incorrectly check the $C200 space. Further Reference o ProDOS 8 Technical Reference Manual o ProDOS 8 Technical Note #21, Identifying ProDOS Devices