CVT GS RAM card jumper settings: (Revision level is on extra leg at bottom) Rev A: - Alone W/Apple card W/4 meg card A and B Rev B: - same configuration with or without an Apple Memory card. 1 MB both under AB 2 MB #1 under BC, #2 under AB 3 MB #1 under AB, #2 under AC 4 MB both under BC CVT RamFast DIP switches (all are set to off from the factory) 1. terminator power (on=yes, off=no) |<| only these two work on 2. Rom: (off=GS, on=//e) |<| version 2.0 and above. 3. Machiene type (off=GS or enhanced //e, on=unenhanced //e) 4. DMA (off=DMA on) 5. GS ROM (on=old, off=ROM 03) 6. RomDisk (off=enable, on=disable) 7. Drive Search timeout (off=30 seconds, on=3 seconds) 8. Reserved (must be off) ZIP GSX Dip Switches: SW 1/1 - ON: cache enable SW 1/2 - OFF: enable joystick SW 1/3 - ON: disable AppleTalk Delay SW 1/4 - OFF: allows GS self test to pass SW 1/5 - OFF: CPS Follow SW 1/6 - ON: enable speed SW 1/7 & 1/8 - Cache size: SW 1/7 1/8 8K ON ON ZipChipGS 16K ON OFF ZipChipGSX, ZipChipGS+ 32K OFF ON 64K OFF OFF SW 2/1 thru SW 2/7 - ON: disable slot delay, (2 is OFF enable delay) SW 2/8 - OFF: speaker delay enable Macintosh Plus, SE SIMM configurations: Memory 1st bank 2nd bank R8/R9 (plus) R35/R36 (SE) 1 MB (2) 256K (2) 256K R8/xx R35/xxx 2 MB (2) 1024K xx/R9 xxx/R36 2.5 MB (2) 1024K (2) 256K xx/xx xxx/xxx 4 MB (2) 1024K (2) 1024K xx/xx xxx/xxx CMS SD 8 DIP switches on back 1. SCSI ID +4 (when Pressed in on the top) 2. SCSI ID +2 ( " " ) 3. SCSI ID +1 ( " " ) 4-7. No connection 8. Reset (must be pressed in at the top for Apple //'s) Apple High Speed DMA SCSI Card DIP switches 1. DMA 2. \ 3. | - SCSI ID 4. / Laser 128 Bottom config switches (rightmost 2 switches if more than 2) Right switch (as seen from bottom)- Down = enable UDC, up = enable slot 7 Left switch - Down (twards keyboard) = enable /RAM5, up = enable slot 5 AE Vulcan DIP switches 1. Interrupt enable (not used) 2. GS=closed, //e,][+=open 3. Boot enable (unenhanced //e,][+=open to boot, otherwise closed) 4. Pseudo-slot enable (closed=PS slot 7) (open=push down on side marked open) Ram 4000 Jumpers: 1 Meg: no jumpers 2 Meg: JP2 3 Meg: Not supported 4 Meg: JP1 and JP2 GS ROM 03 internal Jumper S1 disables Control Panel. Apple Desktop Bus Port pin-outs: (mini-4) 1 ADB data 2 NC Reserved 3 +5V Power 4 GND Ground Apple's GS Memory Expansion Card 1 Meg: no jumpers 2 Meg: Jumper on bottom set of prongs 3 Meg: Not supported 4 Meg: Both jumpers Apple Rev 'C' Card: Put jumper on ID you want for card: 7 is right-most, 0 is left-most pins. Only supports Hard Drives and CD-ROM. Not tape backup, ejectable media, etc. Super Writer 924 DIP Switch Functions: (pressed in at the Top is On=Up, Off=Down) Mode (Switches 1-2) Transparent Down Down ImageWriter Down Up ImageWriter II Up Down ImageWriter LQ Up Up Type (switch 3) B/W Down Color Up Baud (switch 4) 9600 Down 19200 Up Printer (switches 5-8) Blue Chip Up Down Up Up C-Itoth 8510 C-Itoth 8510S Up Down Down Up C-Itoth ProWriter JR+ Down Down Up Up Epson MX Down Down Down Up Epson RX Down Down Up Down Epson FX Down Down Up Up Epson JX Down Up Down Down Epson LQ-1500 Down Up Down Up IBM Graphics Down Up Up Down NEC 8023 Up Down Down Up Okidata 192 Down Up Up Up Okidata 292 Up Down Down Down ProWriter Up Down Down Up Star (old) Down Down Down Down Star XR-1000/1500 Up Up Down Down Star NX-1000 Down Down Up Up Star NX-1000R Down Up Down Down Star XB-2410/2415 Down Up Down Up Star NB10/15 Down Up Down Up Fujitsu DL (color) Down Up Down Down Fujitsu DL B/W Down Up Up Down Fujitsu DX Down Down Up Up Panisonic KXP 1124 Down Up Down Up (and 1534, 1624) Panisonic KXP 1180 Down Down Up Up (and 1191, 1192) Panisonic KXP 1080 Down Down Up Down (and 1091, 1092) 24 Pin (mode=LQ) Down Up Down Up